 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA 1.1GHz Low Power Dual Modulus Prescaler With On-Chip Output Termination The MC12022TSA can be used with CMOS synthesizers requiring positive edges to trigger internal counters such as Motorola's MC145XXX series in a PLL to provide tuning signals up to 1.1GHz in programmable frequency steps. This device is a reduced current drain version of the MC12022A/B with the addition of on-chip output termination. The MC12022TSB can be used with CMOS synthesizers requiring negative edges to trigger internal counters. A Divide Ratio Control (SW) permits selection of a 64/65 or 128/129 divide ratio as desired. The Modulus Control (MC) selects the proper divide number after SW has been biased to select the desired divide ratio. NOTE: The "B" Version Is Not Recommended for New Designs MC12022TSA MC12022TSB MECL PLL COMPONENTS /64/65, /128/129 DUAL MODULUS PRESCALER * * * * * * 1.1 GHz Toggle Frequency Supply Voltage of 4.5 to 5.5V Low-Power 4.0mA Typical Operating Temperature Range of -40 to +85C Short Setup Time (tset) 16ns Maximum @ 1.1GHz P SUFFIX 8-LEAD PLASTIC PACKAGE CASE 626-05 Modulus Control Input Level Is Compatible With Standard CMOS and TTL * Output Load Resistor on Die FUNCTIONAL TABLE SW H H L L MC H L H L Divide Ratio 64 65 128 129 D SUFFIX 8-LEAD PLASTIC SOIC PACKAGE CASE 751-05 Note: SW: H = VCC, L = Open MC: H = 2.0 V to VCC, L = GND to 0.8 V Pinout: 8-Lead Plastic (Top View) IN 8 NC 7 MC 6 GND 5 DESIGN GUIDE Criteria Internal Gate Count* Internal Gate Propagation Delay Internal Gate Power Dissipation Speed Power Product * Equivalent to a two-input NAND gate Value 67 200 0.75 0.15 Unit ea ps mW pJ 1 IN 2 VCC 3 SW 4 OUT MAXIMUM RATINGS Symbol VCC TA Tstg Power Supply Voltage, Pin 2 Operating Temperature Range Storage Temperature Range Characteristic Range -0.5 to + 7.0 -40 to + 85 -65 to + 150 Unit Vdc C C 1/97 (c) Motorola, Inc. 1997 1 REV 3 MC12022TSA MC12022TSB ELECTRICAL CHARACTERISTICS (VCC = 4.5 to 5.5V; TA = -40C to +85C) Symbol ft ICC VIH1 VIL1 VIH2 VIL2 Vout tset Vin Characteristic Toggle Frequency (Sine Wave Input) Supply Current (Pin 2) Modulus Control Input High (MC) Modulus Control Input Low (MC) Divide Ratio Control Input High (SW) Divide Ratio Control Input Low (SW) Output Voltage Swing (CL = 8pF) Modulus Setup Time MC to Out Input Voltage Sensitivity 250-1100 MHz 100-250 MHz 100 400 VCC Open 1.0 VCC Open 1.4 11 16 1500 1500 2.0 Min 0.1 Typ 1.4 4.6 Max 1.1 6.5 VCC 0.8 VCC Open Unit GHz mA V V Vdc -- Vp-p ns mVpp D A C Q D B Q D C Q QB Prop. Delay In QB C QB CM In In Out MC MC Setup D D C QB C Q D QB E Q C D F QB C Q D QB G Q D H C SQ QB MC Out MC Release Modulus setup time MC to out is the MC setup or MC release plus the prop delay. SW Figure 1. Logic Diagram (MC12022TSA) Figure 2. Modulus Setup Time 500 m 20 ns 500 m 20 ns (/64, 500MHz Input Frequency, VCC = 5.0V, TA = 25C, Output Loaded) (/128, 1.1GHz Input Frequency, VCC = 5.0V, TA = 25C, Output Loaded) Figure 3. Typical Output Waveforms MOTOROLA 2 HIPERCOMM BR1334 -- Rev 4 MC12022TSA MC12022TSB VCC = 4.5 to 5.5Vdc C3 Sine Wave Generator C1 50 C2 IN MC GND IN OUT CL EXTERNAL COMPONENTS C1 = C2 = 1000pF C3 = 0.1F CL = 8pF (Including Scope and jig capacitance) VCC SW MC Input Figure 4. AC Test Circuit 200 150 R 100 MHz 50 0 -50 -100 OHMS jX -500 -550 -600 -650 100 -150 -200 -250 -300 -350 -400 -450 200 300 400 500 600 700 800 900 1000 1100 1200 Figure 5. Typical Input Impedance versus Input Frequency HIPERCOMM BR1334 -- Rev 4 3 MOTOROLA MC12022TSA MC12022TSB OUTLINE DIMENSIONS P SUFFIX PLASTIC PACKAGE CASE 626-05 ISSUE K NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 8 5 -B- 1 4 F NOTE 2 -A- L DIM A B C D F G H J K L M N C -T- SEATING PLANE J N D K M M H G 0.13 (0.005) TA M MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --- 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --- 10_ 0.030 0.040 B M A 8 D 5 D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05 ISSUE R C H 0.25 M E 1 4 B M NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ B C e h A SEATING PLANE X 45 _ q 0.10 A1 0.25 B M L CB S A S q Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405; Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 MOTOROLA 4 MC12022TSA/D HIPERCOMM BR1334 -- Rev 4 |
Price & Availability of MC12022TSAD
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |